#Kitchen timer time lapse how to

Set up the shot, wind up the timer, and let it rip at 1/60 of an RPM. The knob, wisely left intact so the amount of time left in the shot is evident, has a matching bolt for the camera’s tripod socket. The timer’s guts were liberated from the case and a simple wooden disc base with a 1/4″-20 threaded insert for a tripod screw was added. Let’s hope ’ time-lapse shots are under an hour, since he based his build on a simple wind-up kitchen timer, the likes of which can be had for a buck or two at just about any store. But they can be a bit bland without a little camera motion, like that provided by a dirt-cheap all-mechanical panning rig. And with good reason – time-lapses are cool. Ikea Cheap and Easy DIY Time Lapse Panning Unit Pr.Seems like the first thing the new GoPro owner wants to do is a time-lapse sequence.

#Kitchen timer time lapse how to

How to Make a Cheap and Easy Ikea Time Lapse Panni.

Mine runs for 2 hours with no issues, but don't complain if you spring snaps at some point!īy the way Ikea have changed Stam now so it is digital, and so doesnt rotate quite so well :( So its just Ordning now. To do this you need to remove the bell (point 2) and remove the little L shaped piece of plastic screwed onto the top. Either pull the top off the timer (it just slides off) and you can remove the smaller, off centre of the two cogs which is the bell rattler by prying off the metal clip on the top of it (its tougher than you think so beware of bendy knives) and the cog just drops off, or if you really want to remove it you can get to the metal rattler by removing the whole timer FROM THE BOTTOM - follow point one to remove the metal timer box then take the three screws ALSO FROM THE BOTTOM and the timer comes out, and you can snap the bell metal off easily.ģ - remove the 60 minute limit. There are two ways to do this, you can do the first or do both (both stops the annoying rattling when its in your pocket). You can just use the top half of the metal, and mount the puck sized unit on whatever you wantĢ - remove the bell. The hole in the plastic base has a screw inside it, take that out and the timer metal box comes out. DO NOT TRY TO DO THIS FROM THE TOP! Remove the three screws that are under the foam on the metal base, then slide the metal off. DO NOT try to take the actual ticking mechanism apart, it explodes and you will never fix it!ġ- remove the entire bottom half, making it much smaller and lighter (eg if you want to mount it on a quadcopter or stack them etc).

Loads of sites say you can't (must not) try to modify these ordning timers, but there are three great improvements you can make with them in a few seconds. My original timer may have looked like junk but its product speaks for itself.īut for those of you (and we know who you are) who are fashion conscious, these new modelsĪre stylish and functional at a bargain price. You can get the set screws at any hardware store, the bushings are harder to find but most cameraįinally, looks. When they break, I unscrew the bushing and the set screw and toss them. That is why I build them as cheap as possible and keep a couple on hand.

Now for reality, the timers in all of these units have cheap plastic components so they will break. In my video I use a drill press, you do not need a drill press, you can do both of these conversions with a hand drill.īoth of these units will sit on a flat surface and spin. The Stam is so cheap why not try to convert it? You do not need to take these timers apart for the conversion. After you add a metal bushing to the Ordning you've got a tough piece of gear. One of the great things about these Ikea timers is that they are cheap. Steampunk, and that's cool right? Well I have been listening and here are my two new designs. I care how well they work,Īnd that they are cheap enough to throw away when they break.

One of the constant comments I get is that they are too hard to build and they are ugly.įrankly, I find them easy to build and I don't care how they look. I guess I'm not the only timelapse photo geek out here. I had no idea the how popular these cheap little gadgets wouldīecome, go figure. I made the original timers for work back in 2008, to provide panning timelapses for extra b-rollįor projects I was shooting. Two years ago I put together the original How To Make An Egg Timer Timelapse Panning Unit.